View LTM15C458T_3411867.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

( 1 / 12 ) 2003 - 11 - 28 (ver. 2.1r) product information features (1) 15.0 type xga display size for monitor (2) 8bit(6bit+frc) data signal with 1ch - lvds interface system (3) wide viewing angle (upper+lower (140 )/ left+right (160 )) (4) 16.19m colors disp lay mechanical specifications item specifications dimensional outline (typ.) 33 1.6 ( w ) x 2 54.7 ( h ) x 13. 5 max( d ) mm number of pixels 1024( w ) x 768( h ) pixels active area 304.128( w ) x 228.096( h ) mm pixel pitch 0.297( w ) x 0.297( h ) weight (approximately) 1 21 0g backlight 4 ccfl, sidelight type absolute maximum ratings item min. max. unit ( v dd ) - 0.3 4.0 v supply voltage ( v fl ) 0 2. 7 kv ( rms ) fl driving frequency ( f fl ) - 100 khz input signal voltage ( v in ) - 0.3 v dd +0.3 v operating temperature 0 50 c storage temperature - 20 60 c storage humidity 10 90 % ( rh ) electrical specification ( recommended operation condition ) item min. typ. max. unit remarks ( v dd ) 3.0 3.3 3.6 v supply voltage ( v fl ) --- 650 --- v ( rms ) i fl =6.0ma ( rms ) fl start voltage ( t a= 0 c) 1500 --- 2000 v ( rms ) differential input voltage( v id ) *1 100 --- 600 m v common mode input voltage ( v cm ) * 1 1.0 --- 2.4 - 1/2 x v id v ( i dd ) *2 --- 380 --- ma current consumption ( i fl ) *3 3 .0 --- 6. 5 ma ( rms ) *2 *3 power consumption (target) -- - 1 6 .9 --- w i fl =6.0ma ( rms ) *1 : refer to thc63lvdm83a/f84a specification by thine electronics, inc. *2 : 8 color bars pattern *3 : excepting the efficiency fl inverter optical specification ( t a=25 c) item min. typ. max. unit remarks luminance --- 350 - -- cd/m 2 i fl =6 .0 ma ( rms ) contrast ratio ( cr ) --- 40 0 --- --- (upper+lower) --- 140 --- viewing angle ( cr >=10) (left+right) --- 160 --- response time t r + t f --- 25 --- ms lamp life time (mtbf)* 4 * 5 50,000 h *4 : conditions ; t a=25 c, i fl =6.0ma(rms), continuous lighting *5 : definitions of failure ; 1) lcd luminance becomes half of the minimum value. 2) lamp doesn ? t light normally. *the information contained herein is presented only as a guide for the app lications of our products. no responsibility is assumed by toshiba matsushita display technology or other rights of the third parties which may result from its use. no license is granted by implication or otherwise under any patent or patent rights of tosh iba matsushita display technology or others. *the information contained herein may be changed without prior notice. it is therefore advisable to contact toshiba matsushita display technology before proceeding with the design of equipment incorporating thi s product. 38cm colour tft - lcd module (15.0 type) ltm15c4 58t (a - si tft) tentative toshiba matsushita display technology co., ltd all information is subject to change without notice. please read bottom notes. www..net
( 2 / 12 ) 2003 - 11 - 28 (ver. 2.1r) 3 ltm15c4 58t dimensional outline (front figure) tentativ e unit: mm standard tolerance: 0.5
( 3 / 12 ) 2003 - 11 - 28 (ver. 2.1r) ltm15c4 58t dimensional outline (back figure) tentative unit: mm standard tolerance: 0.5
( 4 / 12 ) 2003 - 11 - 28 (ver. 2.1r) ltm15c4 58t block diagram 1, 1 2, 1 x n - 1 , 1 x n , 1 1024, 1 1, 2 1, y x n - 1 , y x n , y 1, 768 1024,768 1024 pixels 768 pixels c n 1 c n 2 c n 3 p a n e l c n t r o l l e r g r a y s c a l e m a n i p u l a t i o n v o l t a g e g e n e r a t i o n c i r c u i t c o n n e c t o r y - d r i v e r i c x - d r i v e r i c 1 0 2 4 x 7 6 8 p i x e l s l i q u i d c r y s t a l p a n e l & f l f l f l f l c o n v e r t e r d c / d c l v d s
( 5 / 12 ) 2003 - 11 - 28 (ver. 2.1r) ltm15c4 58t sequence of power supplies and signals r x c k + / - 0 . 2 v 1 0 m s ( m a x . ) 5 0 0 m s ( m i n . ) 3 . 0 v 3 . 0 v 4 0 m s ( m a x . ) 0 m s ( m i n . ) 4 0 m s ( m a x . ) 0 m s ( m i n . ) r x i n 3 + / - r x i n 2 + / - r x i n 0 + / - t h t l o s 0 . 2 v 0 . 2 v v v v d d v 2 5 0 m s ( m i n . ) 0 m s ( m i n . ) v v s f l f l 1 0 % v s f l 1 0 % v f l f l i n p u t v o l t a g e 2 s e c ( m i n . ) 1 0 0 m s ( m a x . )
( 6 / 12 ) 2003 - 11 - 28 (ver. 2.1r) ltm15c4 58t timing chart (3) vertical / horizontal sync timing t 2 t 1 x , y ( 2 ) h o r i z o n t a l t i m i n g ( 1 ) v e r t i c a l t i m i n g n c l k n c l k 2 , y t 4 t 4 t 3 t 4 t 5 t 7 t 6 d e d e x , 7 6 6 x , 7 6 7 x , 7 6 8 x , 1 x , 2 x , 3 x , 4 g 7 - g 0 r 7 - r 0 b 7 - b 0 r 7 - r 0 g 7 - g 0 b 7 - b 0 1 0 2 4 , y 1 0 2 3 , y 1 , y 3 , y 4 , y x n , y tv tvw vsync tvsu tvhd tvbp th hsync tv ?? p ta tb de 767 768 1 2 th thw hsync thfp twde thbp de 1024 pixel data nclk 1 2 3 4 5
( 7 / 12 ) 2003 - 11 - 28 (ver. 2.1r) ltm15c4 58t timing speci fication 1 ) 2 ) 3 ) 4 ) item symbol min. typ. max. unit 790 x t4 - 950 x t4 - frame period t 1 14.28 16.66 17.25 ms vertical display term t 2 768 x t4 768 x t4 768 x t4 - vertical blanking term t 3 22 x t4 - 182 x t4 - 1090 x t4 - 1800 x t4 - 1 line scanning time t 4 15.80 - 28.34 us horizontal display term t 5 1024 x t7 1024 x t7 1024 x t7 - horizontal blanking term t 6 66 x t7 - 776 x t7 - clock period t 7 12.500 - 15.748 ns v - sync pulse width tvw 2 x t4 - - - v - sync set up time tvsu 8 x t7 - - - v - sync hold time tvhd thbp + 16 x t7 - - - vertical front porch tvfp 2 x t4 - - - vertical back porch tvbp 6 x t4 - - - 1090 x t7 - 1800 x t7 - horizontal period th 15.80 - 28.34 us h - sync pulse width thw 8 x t7 - - - horizontal front porch thfp 4 x t7 - 500 x t7 - horizontal back porch thbp 8 x t7 - 492 x t7 - thw + thbp 16 x t7 500 x t7 de pulse width twde 1024 x t7 1024 x t7 1024 x t7 - t3 = tvfp + tvw + tvbp t4 = th t6 = thfp + thw + thbp tvds = tvw + tvbp note 1) refer to ? timing chart ? and lvds (thc63lvdf84a) specifications by thine electronics, inc.. note 2) if enab is fixed to "h" or "l" level for certain period while nclk is supplied, the panel displays black with some flick er. note 3) if nclk is fixed to "h" or "l" level for certain period while enab is supplied, the panel may be damaged. note 4) please adjust lcd operating signal timing and fl driving frequency, to optimize the display quality. there is a possibility th at flicker is observed by the interference of lcd operating signal timing and fl driving condition (especially driving frequency), even if the condition satisfies above timing specifications. note5) do not make t 1, t 2, t3 and tvds fluctuate. if t 1, t 2, t 3 and tvds are fluctuate, the panel displays black. note6) in case of using the long frame period, the deterioration of display quality, noise etc. may be occurred. note7) nclk count of each horizontal scanning time should be always the same . v - blanking period should be ? n ? x ? horizontal scanning time ? . ( n : integer) frame period should be always the same.
( 8 / 12 ) 2003 - 11 - 28 (ver. 2.1r) ltm15c4 58t connector pin assignment for interface cn1 input signal connector: df14h - 20p - 1.25h / hirose mating connector: df14 - 20s - 1.25c / hirose terminal no. symbol function 1 v dd power supply: +3.3v 2 v dd power supply: +3.3v 3 gnd 4 gnd 5 r x in0 - transmission data of pixels 0 (negative: - ) 6 r x n0+ transmission data of pixels 0 (positive: +) 7 gnd 8 r x in1 - transmission data of pixels 1 (negative: - ) 9 r x in1+ transmission data of pixels 1 (p ositive: +) 10 gnd 11 r x in2 - transmission data of pixels 2 (negative: - ) 12 r x in2+ transmission data of pixels 2 (positive: +) 13 gnd 14 r x ck - sampling clock (negative: - ) 15 r x ck+ sampling clock (positive: +) 16 gnd 17 r x in3 - transmission data of pixels 3 (negative: - ) 18 r x in3+ transmission data of pixels 3 (positive: +) 19 gnd 20 nc note 1) nc terminal should be open. cn2 , 3 ccfl power source connector: bhr - 0 4 v s - 1 / japan solderless terminal mfg co., ltd. mating connecto r: sm0 3(7 - d1) b - bhs - 1 / japan solderless terminal mfg co., ltd. terminal no. symbol function 1 v f l h ccfl power supply (high voltage) 2 v f l h ccfl power supply (high voltage) 3 4 v fll ccfl power supply (low voltage)
( 9 / 12 ) 2003 - 11 - 28 (ver. 2.1r) ltm15c4 58t recommend ed transmitter to ltm15c4 58t interface assignment thc63lvdf83a,thc63lvdm83a,thc63lvdm83a - 85 (by thine) input terminal no. input signal (graphics controller output signal) LTM15C458T interface (cn1) symbol terminal symbol function output signal symbol terminal symbol ta0 51 r0 red pixels display data (lsb) ta1 52 r1 red pixels display data ta2 54 r2 red pixels display data ta3 55 r3 red pixels display data ta4 56 r4 red pixels display data ta5 3 r5 red pixels display data ta6 4 g0 green pixels display data(lsb) ta - ta+ no.5 no.6 rxin0 - rxin0+ tb0 6 g1 green pixels display data tb1 7 g2 green pixels display data tb2 11 g3 green pixels display data tb3 12 g4 green pixels displ ay data tb4 14 g5 green pixels display data tb5 15 b0 blue pixels display data (lsb) tb6 19 b1 blue pixels display data tb - tb+ no.8 no.9 rixn1 - rxin1+ tc0 20 b2 blue pixels display data tc1 22 b3 blue pixels display data tc2 23 b4 blue pixels display data tc3 24 b5 blue pixels display data tc4 27 hsync horizontal synchronization signal tc5 28 vsync vertical synchronization signal tc6 30 de compound synchronization signal tc - tc+ no.11 no.12 rxin2 - rxin2+ td0 50 r6 red pixels display data td1 2 r7 red pixels display data (msb) td2 8 g6 green pixels display data td3 10 g7 green pixels display data(msb) td4 16 b6 blue pixels display data td5 18 b7 blue pixels display data (msb) td6 25 res 1) td - td+ no.17 no.18 rxin3 - rxin3+ clk in 31 clk data sampling clock tclk - tclk+ no.14 no.15 clk - clk+ note 1) it is highly recommended to connect this terminal with gnd line. lcd controller is nc (non connection.) g 0 r 5 r 4 r 3 r 2 r 1 r 0 g 5 b 0 b 1 g 4 g 1 b 4 b 5 g 3 g 2 b 2 b 3 t a 0 t b 0 b 7 b 6 g 7 g 6 r 7 r 6 t b 6 t b 5 t b 4 t b 3 t b 2 t b 1 t c 6 t c 5 t c 4 t c 3 t c 2 t c 1 t c 0 t a 3 t a 2 t a 1 t a 4 t a 5 t a 6 t d 6 t d 5 t d 4 t d 3 t d 2 t d 1 t d 0 d e v s y n c h s y n c r x i n 0 r x i n 1 r x i n 2 r x i n 3 r e s
( 10 / 12 ) 2003 - 11 - 28 (ver. 2.1r) ltm15 c4 58t colors combination table display r7 r6 r5 r4 r3 r2 r1 r0 g7 g6 g5 g4 g3 g2 g1 g0 b7 b6 b5 b4 b3 b2 b1 b0 gray scale level black llllllll llllllll llllllll l 0 blue llllllll llllllll hhhhhhhh - green llllllll hhhhhhhh l lllllll - light blue llllllll hhhhhhhh hhhhhhhh - red hhhhhhhh llllllll llllllll - purple hhhhhhhh llllllll hhhhhhhh - yellow hhhhhhhh hhhhhhhh llllllll - basic color white hhhhhhhh hhhhhhhh hhhhhhhh l 255 black llllllll ll llllll llllllll l 0 lllllllh llllllll llllllll l 0 llllllhl llllllll llllllll l 0 llllllhh llllllll llllllll l 0 lllllhll llllllll llllllll l 4 : : : : : : l5 ? l252 hhhhhhlh llllllll llllllll l253 dark - light hhhhhhh l llllllll llllllll l254 gray scale of red red hhhhhhhh llllllll llllllll red l255 black llllllll llllllll llllllll l 0 llllllll lllllllh llllllll l 0 llllllll llllllhl llllllll l 0 llllllll llllllhh llllllll l 0 llllllll lllllhll llllllll l 4 : : : : : : l5 ? l252 llllllll hhhhhhlh llllllll l253 dark - light llllllll hhhhhhhl llllllll l254 gray scale of green green llllllll hhhhhhhh llllllll green l255 black llllllll llllllll llllllll l 0 llllllll llllllll lllllllh l 0 llllllll llllllll llllllhl l 0 llllllll llllllll llllllhh l 0 llllllll llllllll lllllhll l 4 : : : : : : l5 ? l252 llllllll llllllll hhhhhhlh l243 dark - light llllllll llllllll hhhhhhhl l254 gray scale of blue blue llllllll llllllll hhhhhhhh blue l255 black llllllll llllllll llllllll l 0 lllllllh lllllllh lllllllh l 0 llllllhl llllllhl llllllhl l 0 llllllhh llllllhh llllllhh l 0 lllllhll lll llhll lllllhll l 4 : : : : : : l5 ? l252 hhhhhhlh hhhhhhlh hhhhhhlh l253 dark - light hhhhhhhl hhhhhhhl hhhhhhhl l254 gray scale of white & black white hhhhhhhh hhhhhhhh hhhhhhhh white l255
( 11 / 12 ) 2003 - 11 - 28 (ver. 2.1r) ltm15c4 58t reliability test test conditions 1) the module should be driven and inspected under normal test conditions. 2) the module should not have condensation of water (moisture) on the module. 3) the module should be inspected after two or more hours storage in norma l conditions (15 - 35 c,45 - 65%(rh)). 4) a module shall be used only for one test. specifications the module shall have no failure in the following reliability test items. test item test conditions result high temperature operation 1 ) 50 c 192 h ok 3p/3p high temperature storage 2) 60 c 192 h ok 3p/3p high temperature high humidity operation 1) 50 c 80% 192 h ok 3p/3p low temperature operation 1) 0 c 192 h ok 3p/3p low temperature storage 2) - 2 0 c 192 h ok 3p/3p temperature shock 2) - 20 c ? 60 c 0.5h 0.5h 50 cycles ok 3p/3p mechanical vibration 2) 10 - 200 - 10hz sweep/cycle, 1.5 9.8m/s 2 constant, x.y.z each directions, 0.5h each ok 3p/3p mech anical shock 2) 50 9.8m/s 2 , 20ms, x, y, z direction, one time each ok 3p/3p note 1) operating note 2) non - operating definitions of failure for judgment shall be as follows: 1) function of the module should b e maintained. 2) current consumption should be smaller than the specified value. 3) appearance and display quality should not have distinguished degradation. 4) luminance should be larger than 50% of the minimum value specified i n optical specification.
( 12 / 12 ) 2003 - 11 - 28 (ver. 2.1r) ltm15c4 58t for safety lcd module is generally designed with precise parts to achieve light weighted thin mechanical dimensions. in using our modules, make certain that you fully understand and put into practic e the warnings and safety precautions detailed in engineering information no.ee - n001,"cautions and instructions for toshiba lcd modules". refer to individual specifications and technical data sheets (hereinafter called "td") for more detailed technical inf ormation. 1) special purposes a) toshiba matsushita display technology 's standard lcd modules have not been customized for operation in extreme environments or for use in applications where performance failures could be life - threatening or otherwise catastr ophic. b) since toshiba matsushita display technology 's standard lcd modules have not been designed for operation in extreme environments, they must never be used in devices that will be exposed to abnormally high levels of vibration or shock which exceed toshiba matsushita display technology's published specification limits. c) in addition, since toshiba matsushita display technology ? s standard lcd modules have not been designed for use in applications where performance failures could be life - threatening or catastrophic, they must never be installed in aircraft navigation control systems (such as, but not limited to traffic collision avoidance system and air traffic indicator), in military defense or weapons systems, in critical industrial process - control systems (e.g., those involved in the production of nuclear energy), or in critical medical device or patient life - support systems. 2) disassembling or modification do not disassemble or modify the module. it may damage sensitive parts inside lcd module, and may cause scratches or dust on the display. toshiba matsushita display technology doses not warrant the module, if customer disassembled or modified it. 3) breakage of lcd panel do not ingest liquid crystal material, do not inhale this material, and do not contact the material with skin, if lcd panel is broken and liquid crystal material spills out. if liquid crystal material comes into mouth or eyes, rinse mouth or eyes out with water immediately. if this material contact with skin or cloths, wash it off im mediately with alcohol and rinse thoroughly with water. 4) glass of lcd panel be careful with chips of glass that may cause injuring fingers or skin, when the glass is broken. 5) electric shock disconnect power supply before handling lcd module. do not touch t he parts inside lcd module and the fluorescent lamp's connector or cables in order to prevent electric shock, because high voltage is supplied to these parts from the inverter unit while power supply is turned on. 6) absolute maximum ratings and power protec tion circuit do not exceed the absolute maximum rating values under the worst probable conditions caused by the supply voltage variation, input voltage variation, variation in parts' constants, environmental temperature, etc., otherwise lcd module may be d amaged. employ protection circuit for power supply, whenever the specification or td specifies it. suitable protection circuit should be applied for each system design. 7) recommended operation conditions the performance and quality of the lcd panel are warr anted only when the lcd panel is used within ? the recommended operation conditions ? . toshiba matsushita display technology co., ltd. never warrants the performance and quality of the lcd panel when you use the lcd panel over ? the recommended operation cond itions ? , although within ?the absolute maximum rating?. to use the lcd panel over ? the recommended operation conditions ? may have bad influence on the characteristics and reliability of the lcd panel and may shorten the life of the lcd panel . therefore, wh en designing the whole set, not to be over ? the recommended operation conditions ? , you should fully take care of supply voltage change , characteristic of connection parts, serge of input - and - output line, and surrounding temperature. 8) disposal when dispose lcd module, obey to the applicable environmental regulations. !

▲Up To Search▲

Price & Availability of LTM15C458T

	To Download LTM15C458T Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .